hyunaferrin.bsky.social
Summoner Vtuber |
šDNI Any (Ask) | ā§ļø PFP: @Kurifuraa (X)
Mama/Papa : @venividi_vt on Twitter/X
Tags: #HyunaArt #NSFWHyuna #HyunaLive | #HoonahRL #HoonahTuna
Ad. Tags: #ClothkinParty #HyunaCloset
Artist | Cosplayer | Earth-R Summoner | š¦
450 posts
166 followers
315 following
Prolific Poster
Conversation Starter
comment in response to
post
www.twitch.tv/gambanteinn_...
comment in response to
post
www.twitch.tv/gambanteinn_...
comment in response to
post
Detective Outfit/Chicken+Cow Plush: ko-fi.com/itsmarichu
comment in response to
post
Creators of the vtuber assets I will be wearing/using during playthrough!
--
Detective Glasses: ko-fi.com/shylestials
comment in response to
post
As I said, a doozy lol (run away from it)
If I can get a hold of a few peeps I know who also 3D print and tell them what youāre going through, Iāll throw what they suggest or they think may be a cause
comment in response to
post
Mmmmm, from here the only other thing I could recommend besides more manual adjustments isā and this is a doozy, you might need to check and adjust within the gcode.
Iām not wellverse in the coding side of it, but I know itās a more direct change to how your printer will function.
comment in response to
post
Yes, if you want a more accurate read of which side(s) are in level. But if on a budget or auto config is being a b, I would go with the left one first.
Itās simpler to note how much mm the bed is off after a few prints and easier with sliding in one the gauge rulers for a numerical read.
comment in response to
post
Your probe offsets (the pinpoints) may be off when it goes off the bed. You should be able to adjust the āhome positionā of x and y in your settings. If that doesnāt work, you can check if it needs a firmware update, if it needs it.
comment in response to
post
Oops type much, but the best way I could explain it.
comment in response to
post
I pass pre-birfday blessings(July 4th baby) on to you!
YOU GOT THIS! We need the š„ to get his time to shine on them roads.
comment in response to
post
Also just check your filament roll; see if there is any small debris and place it in a cool area when not in use.
With how the weather changes has been, the filament could have needed a change in heating than usual, which could have added to this dilemma, but not been the reason.
comment in response to
post
I want to lean towards internal issue, maybe the cables that attach to the hotend got overheated at one point and now canāt register/or connect the inputed heat that you would adjust at the screen. That would be best case scenario.
Worse case, you would need to see if it hit the motherboard.
comment in response to
post
If bed is off, try getting a leveler to not only manually adjust but to see if you need to replace the bed springs. I was taught to do it by hand cause sometimes the machine will be off.
Pics are a few examples, I use both. But I would recommend the left one for visual of how much off.
comment in response to
post
Mmm, with what you briefly described in your tumblr post and this vid, and if youāve replaced the hotend, it could be an internal problem; psu, cables that are attached or the motherboard.
It sounds like something fried or may just need an internal adjustment; like a zip tie change or soldering.
comment in response to
post
comment in response to
post
Speaks āan eye to catch you on the open seas, may provide a blush of red beyond what is on your cheeks and the color of their skin, but may be the last of such color if fighting on the waters with her.ā
I like tieflings lol
comment in response to
post
Your design speaks kickass and have fun, a lovely combo.
Pirate? Iconic cloak and design, I canāt get enough of that type of fashion.
Blue and Red as the base palettes makes you both stand out but the hues mesh together; almost as if just gentle swirl and you pop up a nice subtle lavender.
comment in response to
post
First thing:
Sucker for subtle gold; just enough to catch your attention.
Goatking? Horns and faun like features? Need. More! The halo crown looks like another set of horns, is a plus!
The color scheme fits close to my favorite color combo and isnāt flashy, seems rather comfy and stylish.